Common issues in coolant pumps
2023-01-16
The coolant pump (typically a belt-driven centrifugal pump) is the heart of the automotive cooling system. The pump circulates coolant through the system while the engine is running to maintain the engine’s optimal temperature.
The coolant also affects other areas of the vehicle, such as the oil passing through the heat exchanger and the EGR (exhaust gas recirculation) valve, making the coolant pump a critical system for normal automotive operation.
Let’s look at some of the common issues that can impact the coolant pump system.
Excessive Use of Sealing Paste
If the coolant pump does not include a gasket, paste is used to seal the pump to the engine block. Applying the right amount of paste is crucial to avoid damaging the internal seal of the pump. If too much paste is used, it can create pollution in the system and damage the mechanical seal. This often leads to coolant pump leakage, which could impact engine operation and potentially cause further damage and engine breakdown.
Do not use any paste on coolant pumps that include a gasket or an O-ring static seal.
If too much paste is used, it can create pollution in the system and damage the mechanical seal.
Polluted or Incorrect Coolant
The dynamic seal separates the “wet” and “dry” areas of the coolant pump. It is important to understand that in order to function correctly, the seal needs the correct and clean coolant. Dirt or other small particles can harm it and drastically reduce the life span of the coolant pump.
While seals on a newly fitted coolant pump may leak slightly at the drain hole, anything beyond this is problematic and likely caused by wrong or polluted cooling fluid. A leaking cylinder head gasket or internal leakage from a water-cooled EGR are common culprits of coolant pollution, which can damage other parts and lead to internal engine defects.
Never mix coolants! The mixing of different types of coolant can lead to major technical issues, as well as create a dangerous chemical mix that may be hazardous.
Never mix coolants! The mixing of different types of coolant can lead to major technical issues, as well as create a dangerous chemical mix that may be hazardous.
Releated
2024-05-28
The braking system is one of the most critical components of a vehicle and has a direct impact on safety. Among the various elements within this system, brake pads are crucial. They ensure that the vehicle stops safely and effectively, making the choice of high-quality pads essential. With more than a century of experience, SKF excels in the development of OE and Aftermarket solutions, including brake rotors with integrated bearings, and offers nearly 900 different brake pad sets for different applications.
2023-01-16
For a steer axle with a 12,000-lb. rating, commonly-accepted pressure is 110 psi, and most drivers assume 85 psi is okay. But for every 10% of underinflation, you’re looking at a 1% reduction in fuel economy. Multiply that by the miles you travel in a year and you can expect:
2023-01-16
We are used to driving our cars with the only concern being when we we need to schedule regular maintenance, but there are some dangerous issues we can avert from happening just by being aware of some not-so-subtle symptoms.
2023-01-16
The wheel bearings on your car can last a lifetime or may not last very long. It all depends on several aspects that we will discuss below. Before talking about replacing wheel bearing, let’s take a quick look at what can cause it to fail.
2023-01-16
It is not necessary to replace both at the same time, however, it is highly recommended due to a high risk of engine damage. All parts of the synchronous drive have the same mileage and wear. If one of the parts is not replaced and loaded again by the timing belt adjustment, this can lead to a failure after a short time. Also, this could save money in the long run as the mechanic only has to do the work to get to the synchronous drive once.
2023-01-16
The timing system is a crucial part of the four-stroke internal combustion engine. Its components drive the synchronized rotation of the camshaft(s), ensuring the engine’s inlet and outlet valves open and close at the proper times. This means that if any of the timing components fail, the car will no longer operate properly, which can cause costly damage to the engine.
2023-01-16
How to grease your vehicle's wheel bearings and which lubricant should be used? SKF has some tips for you on how to take care of your bearings.
2023-01-16
Driveshafts transfer engine torque from the gearbox to the wheel hub at a constant rate, without friction variations or play in cars equipped with an independent suspension system. Driveshafts need to bear stress without creating additional inertia dur to their weight.
2023-01-16
When checking a water pump, you might be confused by the coloured spot on the water pump reservoir. This tinted spot is often associated with coolant leakage; however, it is necessary to make sure that this is not a natural leak. There are several ways to check if the leak is natural. If you're a mechanic, the easiest way is to use a pressure tester like the Cooling System Test & Refill Kit MV4525 from Mityvac. The new patented technology combines simultaneous testing and monitoring of pressure, vacuum, and temperature, providing real-time data that goes far beyond the capabilities of a simple pressure tester.